#CEMENT SKIM COAT WALL FOR FREE#
If you are keen on quality, fare costs seamless interior finishes and a company you can fully trust, call Gypsum Ceiling Supplies for free consultation and estimates. In high humidity areas, use of a bio wash solution is recommended to remove surface fungus growth, fungal spores, mould etc.Use appropriate personal protective equipment.In case of inhalation, move to fresh air and seek medical attention if symptoms persist in both the cases. If symptoms persist, seek medical advice.
#CEMENT SKIM COAT WALL SKIN#
In case of eye and skin contact, wash with plenty of clean water.
Store the product at ambient conditions in well ventilated locations and away from sources of ignition and fire.Ensure good ventilation during application and drying.If the effect of efflorescence is very high then the proper care should be taken to control the efflorescence, Otherwise, Duracoat Internal and External Skimcoat will not stick to the wall and flaking problems may arise. Generally, the cause of efflorescence on the wall surface is due to salty water or salt in sand/bricks. The total thickness of the coats should be limited to a maximum of 2 mm NOTE If at all there is need to remove any unevenness gently level the surface with very fine waterproof emery paper. This breaks down the film formed over it which decreases the water repellency properties. It is recommended not rub the surface done with Duracoat Internal & External Skimcoat strongly and harshly with rough emery paper. After drying of the second coat of skim coat remove any marks with a wet sponge or with a putty blade. Leave the surface to dry overnight/ 10-12 hours. Then apply a second coat of Duracoat Internal & External Skim Coat. After drying of the first coat of Duracoat Internal and External Skim Coat just rub the surface gently with a wet sponge or with a putty blade to remove the loose particles. Suspended Gypsum Ceiling Installation in KenyaĪpply the first coat of Duracoat Internal and External Skimcoat using a blade on the wall.False Gypsum Ceiling Materials in Kenya.This will help in easy application, obtaining more coverage and smooth uniform shade It is very important that mixing of Duracoat Internal & External Skim Coat should be done thoroughly preferably with a mechanical mixer. Continue the mixing for 10-15minutes till a uniform paste is formed. It is important that water be added to the putty to make a mix and not vice versa. MIXING: Slowly mix Duracoat Internal and External Skim Coat with 4045% clean water to make a paste. This ensures higher bonding strength, easy workability and higher coverage with the surface. It is very important and essential that the surface is wet thoroughly before application of Duracoat Internal & External Skim Coat. Moisten the wall with sufficient quantity of clean water. The substrate should clear, free from dust, grease and loose materials. SPREAD RATE: 2-2.5 Sq.Mt/kg/mm depending on surfaceīefore applying Duracoat Internal and External Skimcoat remove all loosely adhering material from the wall surface with the help of sand paper, putty blade or wire brush. It does not contain lead, oil or toxic material Does not require any water curing after application it is ecofriendly.Gives a white and smooth finish surface which effectively reduce the consumption of subsequent pints.Can applied on interior and exterior walls and ceilings.Doesn’t need any kind of primer on it before application of paint thus saving time and cost.Being cementitious it has better adhesiveness and durability with concrete walls.It can be applied on freshly plastered walls thus saving time Duracoat Internal and External Skim Coat has special added polymers and more adhesive strength which provides a strong base ensuring a longer life of the painted surface. Being water resistant, it provides a protective base which prevents expensive paint from flaking. It fills the pores of the walls and ceilings, thereby providing a white, smooth and dry surface for painting. Description Duracoat Skimcoat Product Descriptionĭuracoat Internal and External Skim Coat is a water-resistant white cement-based putty which provides a strong base on concrete/mortar walls and ceilings.
0 kommentar(er)
